Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateTrusted Garage Door Spring Repair for Burnsville Homeowners
A broken spring takes your garage door out of service immediately, and the door usually comes down hard: the opener strains, the door slams, and what used to open with one press stops moving at all. If that’s where you are right now, a garage door spring repair in Burnsville typically runs $180 – $340 for a single spring, and a matched pair costs about twice that. Our technicians have up to 14 years of experience and work exclusively on garage doors, so a snapped torsion or extension spring is a job we see and fix routinely. Spring repair is also one of the most dangerous garage door repairs there is, so it’s not work to attempt at home. We offer same-day service in Burnsville, free estimates, and upfront pricing agreed before we touch the door. Call (844) 443-4836 and we’ll get a specialist out to you.
What Our Garage Door Spring Repair Service Includes
Spring work is a specialty, not a side job. Here’s what each part of the service covers when we come out to a Burnsville home.
Torsion Spring Replacement
Torsion springs are the horizontal coils mounted on the shaft above the door, and they carry most of the door’s weight through every cycle. When one breaks, the door becomes extremely heavy and the opener can’t lift it safely. We replace the failed torsion spring, or the matched pair when both are due, wind the new spring to the manufacturer’s tension for your door’s weight, and test the balance so the door travels smoothly by hand.

Extension Spring Replacement
Extension springs run along the horizontal tracks on either side of the door and stretch as the door lowers. Older Burnsville doors frequently use this setup, and extension springs can fail with enough force to damage the door or the surrounding framing. We replace them with correctly rated springs and bring the door back into proper balance.

Broken Spring Repair
A broken spring is the call we get most often, and it usually announces itself with a loud snap followed by a door that won’t open. Don’t run the opener again once you suspect a break – it only adds stress to the motor and cables. We diagnose which spring failed, confirm the door’s weight, and repair or replace the spring so the door operates normally again.

Spring Adjustment
Springs don’t just break – they also lose tension over time, which makes the door feel heavy or causes it to drift partway open or closed. Adjustment means resetting the spring tension to match the door’s weight so the opener isn’t fighting the springs. We check balance across the full travel of the door and correct any imbalance before it wears out the opener.
Safety Cable Installation
Safety cables run through the center of extension springs and contain the spring if it snaps. Many older installations don’t have them, or have cables that are rusted or frayed. We install or replace safety cables as part of an extension spring job so a future failure stays contained rather than becoming a hazard.
Spring Inspection
A spring inspection checks for the early signs of failure: gaps in the coil, rust, uneven winding, and doors that bind or hesitate. It’s worth doing if your door is more than a few years old or feels heavier than it used to. We’ll tell you what we find and what, if anything, needs replacing – no sales pressure on a door that’s still sound.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Brands We Service for Garage Door Spring Repair
LiftMaster and Chamberlain hardware shows up on plenty of Burnsville doors, and we service both regularly – openers on those systems work with the springs in ways we know well, so we can tell whether a problem is the spring, the opener, or the balance between them. Genie equipment is common too, and we know its quirks when it comes to spring tension and door travel. We also service Clopay doors, which are among the most common residential doors in the region and use standard torsion and extension spring setups that we handle every week.
Whether you have LiftMaster, Chamberlain, Genie, Clopay, or another make entirely, spring repair works the same way from a mechanical standpoint: identify the spring type, confirm the door’s weight, and match the new spring to it. Brand-specific expertise means we recognize the hardware on sight rather than guessing.
Signs You Need Garage Door Spring Repair Right Now
- A loud snap from the garage. That sound is usually a spring breaking, and the door often drops or locks in place right after. Don’t force it open – stop using the opener and call for service.
- The door feels very heavy by hand. A balanced door should lift with modest effort. If you can barely raise it, the spring has lost tension or failed, and the opener is carrying weight it wasn’t designed to.
- The door opens a foot and stops. This usually points to a spring or opener problem, and running the motor against a stuck door risks burning it out. It’s worth a diagnostic before you use it again.
- The door is crooked or binds on one side. One spring working harder than the other causes the door to tilt as it travels. Left alone, it wears out the tracks, rollers, and opener.
- Visible gaps, rust, or stretched coils. A gap in a torsion spring means it’s already broken; rust and sagging on extension springs mean failure is close. Caught early, this is a straightforward repair.
Our Garage Door Spring Repair Process – Step by Step
- 1
Phone diagnosis and scheduling. We ask a few questions about the door, its age, and what it’s doing so we arrive knowing what to expect. Then we set a time that works for you, and for urgent failures we offer same-day service in Burnsville.
- 2
On-site inspection. We check the door’s weight, balance, and travel, look at both springs and their cables, and confirm the opener isn’t contributing to the problem. We use a winding bar and spring gauge rather than eyeballing tension.
- 3
Written estimate before any work. You get the price for the repair in writing, with the parts and labor spelled out, before we start. If something else turns up – a worn cable or roller, say – we tell you and quote it before touching it.
- 4
The repair itself. We wind down the old spring safely, install the new one to the correct tension for your door’s weight, replace safety cables where needed, and reconnect the opener only after the door balances by hand.
- 5
Final test and walkthrough. We cycle the door several times, check the safety reverse, and show you what we did. If anything looks like it will need attention soon, we’ll tell you plainly so you can plan for it.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Spring Repair Cost in Burnsville?
Spring repair in Burnsville typically runs $180 – $340 for one spring, and a matched pair costs about twice that. That range covers the spring itself, the labor to wind and set it correctly, and a final balance and safety check. A broken spring repair on a single-spring door sits in that same $180 – $340 range, while a full pair replacement on a two-spring door lands around double.
Several things move the price within that range. The spring type matters: torsion and extension springs are priced differently, and heavy or oversized doors need heavier springs. Access to the door and the condition of the surrounding hardware – cables, rollers, the opener – can add to the job if those parts are also worn.
To avoid overpaying, ask for the estimate in writing before work starts, and ask whether the quote covers one spring or a pair. A reputable shop tells you plainly when a second spring is worth replacing at the same time rather than after the first one fails. Our free estimates include a full inspection and a written price, so you know exactly what you’re agreeing to before anything is touched. The written estimate sets the final price – no surprises at the end.
Garage Door Spring Repair Near Burnsville – Our Service Area
We serve Burnsville and the surrounding communities, including Apple Valley, Savage, Bloomington, Eagan, Lakeville, Prior Lake, Farmington, and Richfield. If you’re in Burnsville or a nearby suburb, we can usually reach you the same day for a broken spring, and we schedule installations and non-urgent work around your calendar. For related work, see our Burnsville Garage Door Repair Pros home page, or read more about garage door spring repair. We also cover nearby areas with dedicated pages for garage door spring repair in Oakdale and garage door spring repair in Lake Elmo.
Serving Burnsville, MN – Our Local Coverage Area
We serve Burnsville and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Garage Door Spring Repair in Burnsville
Garage door spring repair is the service that restores the springs lifting your door so it opens and closes safely again. It covers replacing a snapped torsion or extension spring, adjusting one that has lost tension, and installing safety cables. Because springs are under high tension, this is not a do-it-yourself job – it’s one of the most dangerous repairs in the trade. Call (844) 443-4836 for a free estimate.
Most single-spring replacements take about an hour to an hour and a half on site. A matched pair takes a bit longer, and if cables or rollers need replacing at the same time, plan on a slightly longer visit. We confirm the timing when you book so you know what to expect.
A single spring replacement typically runs $180 – $340 in Burnsville, and a matched pair costs about twice that. The final price depends on the spring type and the condition of the surrounding hardware, and you get it in writing before any work begins. Call (844) 443-4836 for an exact quote – estimates are free.
Yes, we service Clopay doors and their spring systems as part of our regular work. We also handle LiftMaster, Chamberlain, Genie, and other makes, so you don’t need to find a brand-specific shop. Whether you have Clopay or any other make, we can help.
Yes, emergency garage door service is part of what we do, not an afterthought. A broken spring can leave your door stuck open or locked shut, and we offer same-day service in Burnsville to get it working again. Call (844) 443-4836 and we’ll get a technician out.
We back our spring repair with a satisfaction guarantee on the work we perform. If something isn’t right after the repair, call us and we’ll make it right. The details of what’s covered are spelled out in your written estimate so there’s no confusion.
Clear the area around the door and move cars out of the garage if you can, so the technician has room to work safely. Don’t try to open or close the door before we arrive, and leave the opener switched off. If you have the door’s manual or model information, have it handy – it helps us match the right spring.
Schedule Your Garage Door Spring Repair Service in Burnsville Today
A broken spring won’t fix itself, and every cycle you run against it adds wear to the opener and cables. Call (844) 443-4836 for a free estimate and a written price before any work starts. Our technicians have up to 14 years of experience, we work on garage doors exclusively, and we move fast when a spring fails. One call covers the repair, the balance check, and peace of mind that the door will lift safely again.
Written by the team at Burnsville Garage Door Repair Pros.